Resizing photo to print

[Jerry Thompson]

I am using updated PSCC and a Canon 200 printer. I have an off the camera shot that is 20'''x13.33 a7II. I cannot get it to print an 8x10. All of the info showing on the settings preliminary to printing show 8X10. I am using 8.5X11 paper but the print is not centered and in the 9x7 area of measurement. I tried entering that the paper is 8x10 and did not resize the original and had the resize to fit option checked. PS manages the printing. I'm getting ready to take it too WalMart. As a side not 5X7 prints fine.

 

[wfooshee]

First issue is that 20x13.33 is a different aspect ratio than 10x8, so there will have to be some cropping... Half of 20 is 10, obviously, but half of 13.33 is only 6.66, so you wouldn't have enough image to fill the last 1.33 inches.

Before printing, you need to select an area that fits an 8:10 (or 10:8) ratio and crop your image with that selection, to get the correct aspect ratio for an 8x10 print. Once that's done, PS should handle the printing just fine, I think. Simply telling it to print 8x10 won't work, because your image is a different ratio of length and height.

 

[Jerry Thompson]

First issue is that 20x13.33 is a different aspect ratio than 10x8, so there will have to be some cropping... Half of 20 is 10, obviously, but half of 13.33 is only 6.66, so you wouldn't have enough image to fill the last 1.33 inches.

Before printing, you need to select an area that fits an 8:10 (or 10:8) ratio and crop your image with that selection, to get the correct aspect ratio for an 8x10 print. Once that's done, PS should handle the printing just fine, I think. Simply telling it to print 8x10 won't work, because your image is a different ratio of length and height.

I'll have to figure out how to do that. Any suggestions ?

 

[Jerry Thompson]

I'll have to figure out how to do that. Any suggestions ?

I found out how to do it. Crop to 4x5. Then check image size. It will still show the 3 to 2 ratio. Replace the numbers with an 8 and a 10. All seems good so far. It is too late in the day to try a print. I'll give it a go tomorrow.

 

[Don Fischer]

I am using updated PSCC and a Canon 200 printer. I have an off the camera shot that is 20'''x13.33 a7II. I cannot get it to print an 8x10. All of the info showing on the settings preliminary to printing show 8X10. I am using 8.5X11 paper but the print is not centered and in the 9x7 area of measurement. I tried entering that the paper is 8x10 and did not resize the original and had the resize to fit option checked. PS manages the printing. I'm getting ready to take it too WalMart. As a side not 5X7 prints fine.

No idea what your doing. You print what cone's out of the camera and it's gonna be very small. I use Pixima to go over photo's. With it I choose a size photo I want and feed it in. Could print 3x5, maybe smaller, up to 13x38 on the same photo in the machine. what I don't do is change the pix size on the photo! actually largest I've printed so far is 12x24 inch and comes out great. Smallest was that 3x5. Don't resize the pix out of the camera, just feed in the size photo I want and then adjust the edges to what I want. Very easy and very simple. Has to be, I dumb as a rock with computer stuff! Have done this photo at 4x6 up to 12x24 with the same , guess I'll call it, negative. Don't change the negative size!

 

[snowbear]

Zombie - note to all: Please look at the dates of these "help" threads before replying. This one is from 2023 and OP hasn't been back for seven months.